CONTACT US TODAY

021 556 7203

babs@thesaunashop.co.za

The down-hole drill is a new, highly efficient and extensively applied open-air rock drilling equipment, which is extensively suitable for small and medium sized mines and the projects such as communications, national defense, water conservancy and stonework, in particular the rough and rugged terrains and land forms where other drills are unable to operate normally.
The machine can be used for digging for water and to drill blast holes on mines. It can also be used to drill under roads for cable lines.

The below list is the specifications for the machine.
SM110 Pneumatic and Hydraulic Down Hole Drilling Set Model
Suitable Rock Rigidity(f) 6-20
Bore Dia.(mm) 68-130
Pushing Length(mm) 1000
Rotation Speed(rpm) 0-70
Working Pressure(Mpa) 0.5-0.7
bar 5-7

Air Consumption(m3/min) 3.5-7.2?
cfm 124-424
Max. Pushing Force(N) 4500
Max. Lifting Force(N) 15000
N.W (kg) Drill Part 260
Pumping Station 261
Control Station 50
Appendant 360
G.W (kg) Drill Part 4230
Pumpting Station 330
Control Station 65
Appendant 362

Dimension Drill Part 2180×510×790
Diemension Pumpting Station 1170×980×1050
(L×W×H)(MM) Control Station 700×500×900
Note: Please be advised that you need to mention your depth requirements. The rods all 1m rod.
Please Note This machine is equipped to drill with a mud pump (water pump) or percussion drilling via air compressor. These items are not supplied with the machine.

Product Information
MIG131-Technical Data:
Main Voltage: 230V
Main Frequency: 50Hz
Absorbed Power: 2KW
Mains Fuse: 11A
Power Factor: 0.8
No Load Voltage: 28V
Adjustment Positions: 4 Steps
Current Adjusting Range: 25A / 35A / 50A / 75A
Dia. Usable Wire: Φ0.6mm / Φ0.8mm/Φ0.9mm
Duty Cycle: 20%@75A; 45%@50A; 90%@35A;
100%@25A
Insulation Class: H
Protection Degree: IP21S
Packing Dimension: 665 x 275 x 405mm
Net Weight: 26Kg (Include Acc.)
Gross Weight: 29Kg

DIRECT FROM THE IMPORTERS
NU TECH MACHINERY

www.saunatech.co.za

A telescopic ladder extends and locks by the foot so that the optimum height may be realized. The largest telescopic ladders can extend close to 3.8m. Telescopic ladders are made of aircraft-quality aluminium for lightness and strength. Their ergonomically designed latches are safe and secure when properly used and maintained. Telescopic ladders are more costly than regular step or extension ladders, but their convenience makes them a worthwhile investment. Safety IssuesIt is essential when extending a telescopic ladder to ensure that all safety latches are secure before stepping on the rungs. As with most products, there are slight design differences among telescopic ladders that make the higher-end models more secure than less costly options. Some telescopic ladders can be collapsed section by section. Less expensive models require just one latch to collapse the entire length, which can result in pinched fingers or painful falls for the unwary user.

Also, telescopic ladders should not be used around electrical wiring or during an electrical storm. That’s because telescopic ladders are made of anodized aluminium are therefore good conductors

MIG welding was developed in the 1940′s and 60 years later the general principle is still very much the same. MIG welding uses an arc of electricity to create a short circuit between a continuously fed anode (+ the wire-fed welding gun) and a cathode ( – the metal being welded).
The heat produced by the short circuit, along with a non-reactive (hence inert) gas locally melts the metal and allows them to mix together. Once the heat is removed, the metal begins to cool and solidify, and forms a new piece of fused metal.
A few years ago the full name – Metal Inert Gas (MIG) welding was changed to Gas Metal Arc Welding (GMAW) but if you call it that most people won’t know what the heck your talking about – the name MIG welding has certainly stuck.
MIG welding is useful because you can use it to weld many different types of metals: carbon steel, stainless steel, aluminum, magnesium, copper, nickel, silicon bronze and other alloys.
Here are some advantages to MIG welding:

• The ability to join a wide range of metals and thicknesses
• All-position welding capability
• A good weld bead
• A minimum of weld splatter
• Easy to learn

Here are some disadvantages of MIG welding:

• MIG welding can only be used on thin to medium thick metals
• The use of an inert gas makes this type of welding less portable than arc welding which requires no external source of shielding gas
• Produces a somewhat sloppier and less controlled weld as compared to TIG (Tungsten Inert Gas Welding)

Call Now: 021 5567203

About Patio Heaters

Patio heaters are outdoor heating devices meant to extend use of outdoor recreational and living space into the cooler months like early spring and late fall. They are also referred to as mushrooms or umbrellas due to the covered shape of the heating device, and may be powered by electricity or gas. They are used both by private residences and public facilities.

Function

1. The heating element of a patio heater works by radiating heat from the central chamber through a metal mesh containment cage. Depending on the model, heat may be generated by electric coils or flames fuelled by gas. The heat escapes the chamber through the mesh and is spread downwards onto the space by a wide brimmed and convex cap, shaped like a small umbrella. They can alter the temperature in a radius of about fifteen to twenty feet, and can warm the air temperature up by 25 degrees maximum. Users may control the temperature through a turn-dial setting located on the support column.
   

   Types

2. Patio heaters come in several sizes, but the traditional model is a tall and thin column that supports the heating device. This style is the most effective for heating a large area because the height of this model allows the heat to radiate out across a larger area. However, table top and hanging models are also available.
   

   Features

3. Patio heaters are available in a variety of styles to fit into the decor of the space. Variations are generally available for the width of the support column, colour of metal used, and size of the base. Some residential models are even designed to look like interior floor lamps.
   

   Effects

4. In the past twenty years, patio heaters have become essential appliances for bars and restaurants, as it allows them to keep their outdoor seating spaces open longer and also accommodate patrons who are now not allowed to smoke inside the building due to stricter smoking bans. The Cheesecake Factory restaurants in particular have embraced patio heaters in the design of their cooler climate locations. Luxury hotel chains, like Hilton, Biltmore and Ritz, have also incorporated patio heaters into the designs of their open-air spaces, most notably outdoor entrances and sidewalk awnings.

Call us: 021 556 7203

Different Methods of Digging & Drilling for Water

          Water Wells: Dug, Driven or Drilled

1. Throughout human history, man has had need for wells, although the way that we go about digging our wells today is very different than how our ancestors dug them. A water well is an excavation down to access groundwater in underground aquifers. Water can be drawn up using a hand pump, a mechanical pump, an electric submersible pump, or a vertical turbine pump, in addition to being removed in containers raised by hand. Well water typically contains more minerals than surface water and may require water softening treatments to remove iron, manganese, arsenic, and others. Wells today are created either by digging, driving or drilling.
   

   Digging Wells and Driving Wells

2. Until recent times, all wells were pumpless affairs that were hand-dug, and therefore typically had to be at least wide enough to accommodate men with digging tools. Today, digging is still an option, even an attractive one in rural areas, where labour may be in greater supply than technology. Reinforced concrete well rings are lowered into the hole, and the well digging team digs under the cutting ring while the well column slowly sinks into the aquifer. Hand-dug wells are cheap and low-tech, and have been dug successfully up to 60 meters into the ground. Further, hand-dug wells have low operation and maintenance costs. However, construction can be dangerous due to collapsing earth, falling rocks and asphyxiation. Wells today are occasionally driven as well, using a hardened drive point and a perforated pipe. The point is driven into the ground with the stability of a tripod and a "drive," and pipe sections are added as needed. Once the water table is encountered, the well sediment is flushed out, and a pump is installed.
   

   Drilling Wells

3. Drilling wells can produced with simple hand methods, like sludging, or auguring, but more commonly are done with machine drilling tools. These machine tools use some combination of rotary and percussive forces to get water from a much deeper level than dug wells–up to several hundreds of meters. Wells drilled with electric pumps are the standard throughout the world, especially in sparsely populated areas. Most drilling machines for shallow wells are mounted on large trucks or trailers. Drilling is accomplished with a bit, which rotates into and breaks up the rock. Then a typically steel or plastic PVC factory-made pipe is inserted.

Technorati Tags: Borehole drilling,boreholes,borehole drilling cape town,Borehole drilling south africa

MIG Welding Tips for Filling Gaps

MIG welding is the process of using inert gas to create a solid weld. During this process metal is fed through a trigger mechanism into the welding flame and bonded with metal. The process involves the use of filler bars to complete welds and fill in gaps. It is another facet of this style of welding and one that beginners need to master in order to be proficient.

Choosing Filler Bars

A filler bar is a stick of metal that is used with the MIG welding process to fill in a gap in a seam or welded joint. Selecting the right filler bar is the first step in mastering this process. Filler bars are numbered corresponding to their makeup and thickness. These numbers will correlate to specific types of welds and materials, for instance aluminium, steel and stainless steel just to name a few. Keep a number of filler bars on hand and select them based on the type of material and its thickness used in your weld.

Tools

It always helps to have the right tools, and in welding these are varied. One useful tool to have on hand is a large file. This is used to file down the weld, seam and other parts of the material you are using. This is especially useful when you stop a weld and then pick it back up after the metal has cooled. Filing the welder tip will remove some of the flux metal and make it easier to get back to what you are doing.

Using the Right Gas

Another reason some welds fail is due to the type of gas used. When you start a project use the right type of gas for the material you are welding. This also is called shielding gas because it forms a protective barrier around the two metals allowing them to join together more firmly. For thicker metals and steel, use CO2 for instance. This gas burns hot so it gets into the weld faster. However, this gas is too hot for a thinner metal or material like aluminium siding. A mixture of Argon and CO2 (75 percent Argon and 25 percent CO2) is a better solution for thin metal

You can also visit migweldersdirect;sa-importersdirect;saimportersdirect;saimporters;capesolargeyser and hitempsolar

Call: 0215567203

See website

Getting into shape is now a breeze with the new slimming belt, we know your slimming needs and what better way to do it with a multi-pronged approach that targets the various body parts effectively.

The Patented Twin Power Slimming Belt is a brilliant invention that capitalises on symmetrical double-point massage.  Its two separate massagers provide a well-balanced treatment, zapping away unwanted fats at your tummy, butt, thighs and other area more effectively and efficiently.

The Twin Power also gives you a harmonious massage like no other, returning you

a deserved relaxation after a hard days work.  You can feel an instant difference because the oscillating

motion distinguishes itself from conventional devices that rely merely on vibration.

With warm air circulating around the essential points of contact, sit back and feel recharged with an improved blood circulation.  Chase away lactic acid and relieve muscle fatigue with this exclusive heating function.

Your personal Fitness massager is elaborately coded with a heat-balancing act. The 4 ventilation outlets fitted within the belt allow a quick regulation of heat, maintaining optimum performance while you Zap.

Call: 0215567203

See website

1Person FIR Sauna Room with glass Tinting
D:Outside light
Dimensions:900X1050X1900(mm)
Capacity:1Person & a Half

Dual control panel: Yes
Far Infra red Heaters: 3pcs
Operating temperature:18-60 d/c
Power: 1200W
Wood: Cedar /Can.Hemlock

FM/CD Player: Yes
Package: 2 Cartons

Call: 0215567203

See website

2 Person far infrared Sauna Room (Wellness Cabin)
D:Outside light
Dimensions:1200X1200X1900(mm)
Capacity:2Person & a Half
Dual control panel: Yes
Far Infra red Heaters: 5pcs
Operating temperature:18-60 d/c
Power: 1600W
Wood:Cedar /Can.Hemlock

FM/CD Player: Yes
Package: 2 Cartons